Additional post-upgrade steps for NetApp clusters
After a NetBackup upgrade, review your NetApp cluster configuration as additional steps may be required to insure everything continues to work as expected. Table: Additional required NetApp cluster changes lists the various configurations and how to proceed.
Caution:
If at any time after the upgrade the mode changes from Node scope to Vserver aware, you must perform the additional steps. Failure to perform the additional steps places your data at risk.
Table: Additional required NetApp cluster changes
NetApp cluster mode at time of upgrade | Changes to NetApp cluster mode after upgrade | More information |
|---|---|---|
Node scope mode | No changes | NetBackup and NetApp both recommend that you change to Vserver aware mode at your earliest convenience. |
Node scope mode | Change to Vserver aware mode | Additional steps required. See “Additional changes for Node scope mode to Vserver aware mode”. |
Vserver aware mode | Not applicable | Additional steps required. See “Additional changes required for NetApp clusters in Vserver aware mode”. |
Note:
Once a media server detects Vserver aware mode, no further backup activities are performed on any other media server running any earlier releases of NetBackup.
If you change from Node scope mode to Vserver aware mode, you must do the following:
Additional changes for Node scope mode to Vserver aware mode
- Enable the Vserver aware mode on the cluster by disabling node-scope-mode.
- If there are tape devices attached to the cluster nodes, you must reconfigure them. Configure the tape devices to use the cluster-management logical interface (LIF) as the NDMP host for the device configuration. NetBackup does not support use of node name for device configuration.
See the NetBackup NAS Administrator's Guide for additional information.
- Credential all the LIF that are used for backups.
This activity includes the Cluster Management LIF as well as any Vserver Data LIFs that are used for backup policies.
See the NetBackup NAS Administrator's Guide for additional information.
- Update the database for all existing NDMP hosts in your environment. Use the command that is shown to update the database.
tpautoconf - verify NDMP_host_name
- Update or replace any storage units that use the node names of the cluster to use the cluster LIF.
- Update or replace any existing policies that back up the cluster.
You must use either the Data LIF or the Cluster-management LIF as the client name. NetBackup does not support the use of the node name for the client name. The backup selections may also need to be modified.
- Add an intercluster management LIF for each node that does not host a cluster management LIF.
The NetApp cluster requires this activity to perform NDMP 3 way or NDMP Remote backups. Without these LIFs, all 3 way or remote backups from the volumes that are not hosted on the same node as the cluster management LIF fail.
- To restore, verify, or duplicate the old images, you may have to use alternate read host.
Additional changes required for NetApp clusters in Vserver aware mode
- Run tpautoconf command on each Vserver. This command must be run from the media servers that have credentials to the Vserver.
tpautoconf - verify ndmp_host
Once the command runs successfully, the output of the nbemmcmd should look similar to the following:
servername1@/>nbemmcmd -listsettings -machinename machinename123 - machinetype ndmp NBEMMCMD, Version: 10.1 The following configuration settings were found: NAS_OS_VERSION="NetApp Release 8.2P3 Cluster-Mode" NAS_CDOT_BACKUP="1" Command completed successfully. NAS_OS_VERSION displays the NetApp Version. NAS_CDOT_BACKUP tells us if NetBackup uses the new cDOT capabilities.
The tpautoconf - verify ndmp_host command is not required when a new Vserver is added.
- Add devices to the NDMP cluster as necessary and access them using the cluster management LIF. As you add devices, you must discover the devices.
- Add storage units for the newly discovered devices.
- Update any existing policies that back up the cluster.
You must use either the Data LIF or the Cluster-management LIF as the client name. NetBackup does not support the use of the node name for the client name. The backup selections may also need to be modified.