About obtaining IP addresses for Veritas Access
The Veritas Access initial configuration process requires that you configure several IP addresses for the two appliance nodes.
You can configure a pure IPv4 or an IPv6 network, or a mixed mode network with both IPv4 and IPv6 addresses.
Note:
The IP type (IPv4 or IPv6) can be different on different networks. In a single network, the IP type must be consistent (either IPv4 or IPv6).
Table:
eth1 | eth2 and eth3 | eth4 and eth5 (for Access 3340 Appliance model) eth4 and eth6 (for Access 3350 Appliance model) | Console IP |
|---|---|---|---|
IPv4 | IPv4 | IPv4 | IPv4 |
IPv4 | IPv4 | IPv6 | IPv4 |
IPv6 | IPv4 | IPv6 | IPv6 |
IPv6 | IPv4 | IPv4 | IPv6 |
You need to obtain a range of physical IP addresses, a range of virtual IP addresses, and a netmask for the chosen public network from the network administrator in charge of the facility where the appliance is located. The range of IP addresses need not be contiguous as long as the IP addresses are in the same data network. All IP addresses (both physical and virtual) must be part of the same subnet and use the same netmask as the node's access IP.
By design, the appliance does not support the use of the localhost (127.0.0.1) IP address during configuration.
Note:
Netmask is used for IPv4 addresses. Prefix is used for IPv6 addresses. Accepted ranges for prefixes are 0-128 (integers) for IPv6 addresses.
The information you obtain from the network administrator is used to configure the following:
Physical IP addresses
Virtual IP addresses
Console IP address
IP address for the default gateway
Netmask for the data network
Details for the private network, such as starting IP address and the netmask for the private IP address
(Optional) IP address for the Domain Name System (DNS) server
DNS domain name
NTP server
Note:
If the FQDN of the NTP server is specified, you are required to configure the DNS server.
Table: Required IP addresses
Number of IPs | Item |
|---|---|
0 to 4 | Physical IP addresses for public network access over eth4 and eth5 for the Access 3340 Appliance model or over eth4 and eth6 for the Access 3350 Appliance model. You can configure up to four public IP addresses. The IP addresses are assigned to the public interfaces of both the nodes using the round-robin algorithm, selecting the first public interface of both the nodes followed by the second public interface of both the nodes. |
0 to 8 (Optional) | Virtual IP addresses for public network access over eth4 and eth5 for the Access 3340 Appliance model or over eth4 and eth6 for the Access 3350 Appliance model. Starting with version 8.0, you can assign a virtual IP address to a public data network interface that does not have a physical IP address assigned to it. Earlier, a physical IP address was required to be assigned to a public data network interface if you wanted to assign a virtual IP address to it. |
1 | IP address for the management console. |
2 | IP addresses for or appliance node management over IPMI. |
2 | IP addresses for appliance node management over eth1. |
For more details about Veritas Access network requirements, refer to the Veritas Access Installation Guide.
See Where to find the documentation.
You can configure network bonding to group multiple network interfaces into a single logical interface. The bonded network interface increases data throughput and provides redundancy.
For the Access 3340 Appliance model, when you configure network bonding for public network access, bond0 is created, which groups eth4 (pubeth0) and eth5 (pubeth1) into a single logical network interface. For the Access 3350 Appliance model, when you configure network bonding for public network access, bond0 is created, which groups eth4 (pubeth0) and eth6 (pubeth2) into a single logical network interface.
Use the following guidelines when you assign an IP address for the bonded network interface:
Allocate either IPV4 public and virtual IP addresses or IPV6 public and virtual IP addresses, but not both.
Reserve a maximum of two public IP addresses for public network access. The IP addresses need not be contiguous.
Reserve one virtual IP address for the Remote Management Console.
More Information