Upgrading OpsCenter silently
Use the following procedures to upgrade to OpsCenter components silently.
To upgrade OpsCenter
- If you are using OpsCenter to monitor NetBackup, ensure that you upgrade OpsCenter before upgrading NetBackup.
- Log on as administrator to the OpsCenter system that you want to upgrade.
- Insert the appropriate OpsCenter DVD in the DVD drive.
- Open the command prompt on your system.
Navigate to
<DVD Drive>\<Architecture>\Serverdirectory. - Enter the following command:
SETUP.EXE -NoInstall
Note that the -NoInstall switch is case-sensitive .
This command starts the Installation Wizard where you can specify your preferences. Note that the Installation Wizard creates the response file based on your inputs and does not install the product.
- The Installation Wizard detects an existing installation of OpsCenter on the system. For example, the following message may be displayed on the Welcome screen:
The installer has detected that OpsCenter Server is already installed on your system that will now be upgraded to version.
Click Next.
- Read the license agreement, check I accept the terms of the license agreement and click Next.
You may opt to check or uncheck Participate in the NetBackup Product Improvement Program. This option is checked by default.
If this option is checked, OpsCenter will automatically upload installation deployment and product usage information to the OpsCenter development and support teams in a secured manner. This data would be used to guide future product development and also analyze issues. For more information, refer to the About the NetBackup Product Improvement Program section in the NetBackup Installation Guide.
- In the Installation Method section, click Typical to use the default settings, installation location, or port numbers. Typical is selected by default.
Also compare the space that is required for installing OpsCenter server and the actual space that is available.
Click Next.
Note:
The Custom option is disabled when you upgrade from to OpsCenter. You cannot customize the default settings, locations, or port numbers while upgrading to OpsCenter.
- Specify a location for saving the old OpsCenter database. The default location is
C:\Program Files\Symantec\OpsCenter_SavedData.Warning:
In case of sequential OpsCenter upgrades (for example, version 1 > version 2 > version 3), the old
OpsCenter_SavedDatafolder may already exist. If theOpsCenter_SavedDatafolder is overwritten during upgrade, the OpsCenter GUI may not start properly. To avoid this problem, you should rename the oldOpsCenter_SavedDatafolder before upgrading to OpsCenter.Click Browse to specify a different location.
In case the directory
C:\Program Files\Symantec\OpsCenter_SavedDatadoes not exist, you are prompted to create it. Click Yes to create the directory.Note:
Ensure that the database location has adequate space by going through the Disk space requirements section on this page. A green checkmark appears in the Required column if there is adequate disk space.
- On the License Keys panel, enter your demo or permanent key that you have received with the purchase of OpsCenter and click Add Key.
See OpsCenter Analytics license keys.
Click Next.
- The installer shows a summary of the installation settings.
Check Save Summary to option to save the installation summary. Click Browse to save the installation summary in your preferred location.
Click Install. Note that clicking Install does not install the product.
- The Installation Status panel is displayed. Click Finish.
- A response file named
Server-<DD-MM-YY-HH-MIN-SS>.XMLis created at the following location:C:\windows\temp\Symantec\OpsCenterThis XML file can be used to upgrade OpsCenter Server software on multiple computers.
- On the command prompt, ensure that you are in the directory where
SETUP.EXEis located. - Enter the following command to run the silent installation:
SETUP -Silent -RespFile<path of the response file>
Example:Setup -Silent -RespFile C:\Server-07-12-10-06-11-31.xml
Note that the switches -Silent and -RespFile are case-sensitive .
- The installation logs are generated in the following location:
%ALLUSERSPROFILE%\Symantec\OpsCenter\ INSTALLLOGS\OpsCenterServerInstallLog.htm.If you run the installer in a maintenance mode later,
OpsCenterServerMaintenanceInstallLog.htmis also generated in the same location.See the following section to track the progress of the installation.
See About tracking the progress of silent installation.
After successful installation, you can see the OpsCenter Server entry in Add/Remove Programs.
To upgrade OpsCenter View Builder silently
- Log on as administrator to the OpsCenter View Builder system that you want to upgrade.
- Insert the appropriate OpsCenter DVD in the DVD drive.
- Open the command prompt on your system.
Navigate to
<DVD Drive>\<Architecture>\ViewBuilderdirectory.Example:
D:\x86\ViewBuilder - Enter the following command:
SETUP.EXE -NoInstall
Note that the -NoInstall switch is case-sensitive .
This command starts the Installation Wizard where you can specify your preferences. Note that the Installation Wizard creates the response file based on your inputs and does not install the product.
- The OpsCenter Installation Wizard appears. The Installation Wizard detects an existing OpsCenter View Builder and shows the following message on the Welcome panel:
The installer has detected that OpsCenter View Builder old_version is already installed on your system that will now be upgraded to current_version.
Click Next to continue.
- Read the license agreement, check I accept the terms of the license agreement and click Next.
You may opt to check or uncheck Participate in the NetBackup Product Improvement Program. This option is checked by default.
If this option is checked, OpsCenter will automatically upload installation deployment and product usage information to the OpsCenter development and support teams in a secured manner. This data would be used to guide future product development and also analyze issues. For more information, refer to the About the NetBackup Product Improvement Program section in the NetBackup Installation Guide.
- The installer shows a summary of the settings that you have selected for OpsCenter View Builder installation. Check Save Summary to field to save the installation summary. Click Browse to save the installation summary in your preferred location.
Click Install.
- A response file named
ViewBuilder-<DD-MM-YY-HH-MIN-SS>.XMLis created at the following location:C:\windows\temp\Symantec\OpsCenterThis XML file can be used to upgrade OpsCenter View Builder software on multiple computers.
- On the command prompt, ensure that you are in the directory where
SETUP.EXEis located. - Enter the following command to run silent installation:
Setup -Silent -RespFile <path of the response file>
Example: Setup -Silent -RespFile C:\ViewBuilder-07-12-10-06-11-31.xml
Note that the switches -Silent and -RespFile are case-sensitive .
- The installation logs are generated in the following location:
%ALLUSERSPROFILE%\Symantec\OpsCenter\ INSTALLLOGS\OpsCenterViewBuilderInstallLog.htm.If you run the installer in a maintenance mode later,
OpsCenterViewBuilderMaintenanceInstallLog.htmis also generated in the same location.See the following section to track the progress of the installation.
See About tracking the progress of silent installation.
After successful installation, you can see OpsCenter View Builder in Add/Remove Programs.