Media properties
To access this setting, in the web UI select . Select the server. If necessary, click . Then click or . Click .
The Media host properties contain the following settings.
Table: Media properties
Property | Description |
|---|---|
This property overrides the NetBackup overwrite protection for specific media types. Normally, NetBackup does not overwrite certain media types. To disable overwrite protection, place a check in the check box of one or more of the listed media formats. For example, place a check in the CPIO check box to permit NetBackup to overwrite the cpio format. By default, NetBackup does not overwrite any of the formats on removable media, and logs an error if an overwrite attempt occurs. This format recognition requires that the first variable length block on a media be less than or equal to 32 kilobytes. The following media formats on removable media can be selected to be overwritten:
| |
|
This property allows exclusive access protection for tape drives. With access protection, other host bus adaptors cannot issue commands to control the drives during the reservation. SCSI reservations provide protection for NetBackup Shared Storage Option environments or any other multiple-initiator environment in which drives are shared. The protection setting configures access protection for all tape drives from the media server on which the option is configured. You can override the media server setting for any drive path from that media server. See Recommended use for Enable SCSI reserve property. The following are the protection options:
Note: Ensure that all of your hardware processes SCSI persistent reserve commands correctly. All of your hardware includes Fibre Channel bridges. If the hardware does not process SCSI persistent reserve commands correctly and NetBackup is configured to use SCSI persistent reserve, no protection may exist. | |
This property lets NetBackup mix retention levels on tape volumes. It applies to media in both robotic drives and nonrobotic drives. The default is that the check box is clear and each volume can contain backups of only a single retention level. | |
This property, when checked, lets backups span to multiple tape media. This property lets NetBackup select another volume to begin the next fragment. The resulting backup has data fragments on more than one volume. The default is that is checked and backups are allowed to span media. If the end of media is encountered and this property is not selected, the media is set to FULL and the operation terminates abnormally. This action applies to both robotic drives and nonrobotic drives. | |
This property lets backups span disk volumes when one disk volume becomes full. The default is that this property is enabled. The Allow backups to span disk volumes property does not apply to AdvancedDisk or OpenStorage storage units. Backups span disk volumes within disk pools automatically. The following destinations support disk spanning:
For disk spanning to occur, the following conditions must be met:
| |
This property lets NetBackup use whatever labeled or unlabeled media is found in a nonrobotic drive. The default is that the property is enabled. | |
This property allows the logging of the job information. This logging is the same information that the NetBackup Activity monitor uses. The default is that job logging occurs. | |
|
This property controls media sharing, as follows:
The default is that media sharing is disabled. (The property is cleared and no server groups are configured.) | |
This property specifies the media ID prefix to use in media IDs when the unlabeled media is in nonrobotic drives. The prefix must be one to three alpha-numeric characters. NetBackup appends numeric characters. By default, NetBackup uses A and assigns media IDs such as A00000, A00001, and so on. For example, if FEB is specified, NetBackup appends the remaining numeric characters. The assigned media IDs become FEB000, FEB001, and so on. | |
To specify a property indicates that the unloading of media is delayed after the requested operation is complete. Media unmount delay applies only to user operations, to include backups and restores of database agent clients, such as those running NetBackup for Oracle. The delay reduces unnecessary media unmounts and the positioning of media in cases where the media is requested again a short time later. The delay can range from 0 seconds to 1800 seconds. The default is 180 seconds. If you specify 0, the media unmount occurs immediately upon completion of the requested operation. Values greater than 1800 are set to 1800. | |
This property specifies how long NetBackup waits for media in nonrobotic drives. During the delay period, NetBackup checks every 60 seconds to see if the drive is ready. If the drive is ready, NetBackup uses it. Otherwise, NetBackup waits another 60 seconds and checks again. If the total delay is not a multiple of 60, the last wait is the remainder. If the delay is less than 60 seconds, NetBackup checks after the end of the delay. For example, set the delay to 150 seconds. NetBackup waits 60 seconds, checks for ready, waits 60 seconds, checks for ready, waits 30 seconds, and checks for ready the last time. If the delay was 50 seconds (a short delay is not recommended), NetBackup checks after 50 seconds. |