NetBackup disaster recovery email example
A catalog backup policy can send a disaster recovery email upon completion of a catalog backup. To configure a catalog backup policy, see the NetBackup Administrator's Guide, Volume I:
https://support.cohesity.com/s/article/article-100040135
The following is an example of a disaster recovery email after a successful catalog backup:
From: NetBackup@example.com
Sent: Tuesday, June 13, 2023 04:42
To: NetBackup Administrator
Subject: NetBackup Catalog Backup successful on host
primary.example.com status 0
Attachments: cat_1686692545_FULL.drpkg
Server
primary.example.com
NetBackup Version
10.3
Date
6/13/2023 04:42:20 PM
Policy
cat
Catalog Backup Status
the requested operation was successfully completed (status 0).
DR image file: /usr/openv/cat_1686692545_FULL
To ensure that the NetBackup catalog data is protected through
Tue 13 Jun 2023 04:42:20 PM CDT, retain a copy of each attached file, and
the media or files listed below:
Catalog Recovery Media
Media Server Disk Image Path Image File Required
* media-server.example.com @aaaab cat_1686692540_FULL
* media-server.example.com @aaaab cat_1686692545_FULL
* media-server.example.com @aaaab cat_1686692545_FULL
DR file written to
/usr/openv/cat_1686692545_FULL
DR Package file written to
/usr/openv/cat_1686692545_FULL.drpkg
The CA configuration at the time of catalog backup is as follows:
The primary server primary.example.com is configured to use NetBackup certificates.
ECA_CRL_PATH_SYNC_HOURS = 1
ECA_CRL_REFRESH_HOURS = 24
ECA_CRL_CHECK = LEAF
The primary server is configured to use service account: root
The primary server is configured to run with FIPS mode set to: DISABLE
* - Primary Media
Catalog Recovery Procedure for the Loss of an Entire Catalog
You should create a detailed disaster recovery plan to follow should it become
necessary to restore your organization's data in the event of a disaster. A
checklist of required tasks can be a tremendous tool in assisting associates in
triage. For example, after the facility is safe for data to be restored, the
power and data infrastructure need to be verified. When these tasks are
completed, the following scenarios will help to quickly restore the NetBackup
environment, and in turn, restore applications and data.
Disaster Recovery Procedure using the DR Package file and DR Image File
In the event of a catastrophic failure, use the following procedure to rebuild
the previous NetBackup environment.
Important Notes:
- If new hardware is required, make sure that the devices contain drives
capable of reading the media and that the drive controllers are capable of
mounting the drives.
- Keep the passphrase associated with the DR Package file handy. This
passphrase is set before the catalog backup policy configuration using the
NetBackup web UI or the nbseccmd command.
- If the catalog backup is encrypted using keys from an External KMS, configure
the External KMS in NetBackup after the installation completes and before
starting recovery. See the NetBackup Security and Encryption Guide for
information on how to configure an external KMS.
https://support.cohesity.com/s/article/article-100040135
- If this catalog backup is encrypted using a keys from the NetBackup KMS,
configure the NetBackup KMS and restore the required keys after the installation
completes and before starting recovery. See the NetBackup Security and
Encryption Guide for information on how to backup and restore keys from the
NetBackup KMS. https://support.cohesity.com/s/article/article-100040135
1. Install NetBackup.
a. The installation procedure prompts you to confirm if this is a DR
scenario.
i. On the UNIX installer, you can see a prompt as "Are you currently
performing a disaster recovery of a primary server? [y,n] (y)".
Select "y"
ii. On the Windows installer click the "Disaster Recovery Primary
Server" button.
b. The installation procedure prompts you for the primary server's DR
Package
(refer to the /usr/openv/cat_1686692545_FULL.drpkg mentioned earlier).
Make sure that the primary server can access the attached DR package
file.
c. Type the passphrase associated with the DR Package,
when prompted.
i. The installer validates the DR package using the passphrase.
ii. In case of errors in validation, the installer aborts the
operation. To work around the issue, refer to the following
article: https://support.cohesity.com/s/article/article-100033743
iii. If the external CA-signed certificates could not be backed up,
configure the certificates on the host.
Refer to the following article:
https://support.cohesity.com/s/article/article-100044249
2. Configure the devices necessary to read the media listed above.
3. Inventory the media.
4. Make sure that the primary server can access the attached DR image file.
5. Start the NetBackup Recovery Wizard from the NetBackup web UI. Or, start
the wizard from a command line by entering bprecover -wizard.
Disaster Recovery Procedure without the DR Image File
NOTE: ONLY ATTEMPT THIS AS A LAST RESORT
If you do not have the attachment included with this email, use the following
instructions to recover your catalog. (If using OpenStorage disk pools, refer
to the Shared Storage Guide to configure the disk pools instead of step 2 and
3 below ):
1. Install NetBackup.
2. Run:
Configure certificates for the media server that is associated with this
catalog recovery by running the below commands on that host:
nbcertcmd -getCACertificate
nbcertcmd -getCertificate -force
3. Configure the devices necessary to read the media listed above.
4. Inventory the media.
5. Run
To recover from copy 1:
bpimport -create_db_info [-server name] -id /
6. Run:
cat_export -client client1.example.com
7. Go to the following directory to find the DR image file
cat_backup_1686692545_FULL:
/usr/openv/netbackup/db.export/images/primary.example.com/1686000000
8. Open cat_backup_1686692545_FULL file and find the BACKUP_ID
(for example: primary.example.com_1686692545).
9. Run:
bpimport [-server name] -backupid primary.example.com_1686692545
10. Run:
bprestore -T -w [-L progress_log] -C primary.example.com -t 35
-p cat_backup -X -s 1686692545 -e 1686692545 /
11. Run the NetBackup web UI to restore the remaining image database
if the DR image is a result of an incremental backup.
12. To recover the NetBackup relational database, run:
bprecover -r -nbdb
13. Stop and start NetBackup.
14. Run:
Re-configure the certificates on the primary server and the media server,
because the database is restored to a previous point in time.
Run the following set of commands on the primary server:
nbcertcmd -getCACertificate -force
nbcertcmd -createToken -reissue -host <primary/media>
name <>
nbcertcmd -getCertificate -token <> -force
Run the following set of commands on the media server that is
associated with this catalog recovery:
nbcertcmd -getCACertificate -force
nbcertcmd -getCertificate -force
15. Configure the devices if any device has changed since the last
backup.
16. To make sure the volume information is updated, inventory the
media to update the NetBackup database.More Information